Knowing how to put lights on a Christmas tree sounds simple until you are standing in the sitting room with a tangle of wire, a tree that is half built and no idea whether the box in your hand is enough. The two questions that decide how it turns out are how you run the string and how many lights the tree needs. This guide answers both, using the light counts of real trees we sell as the yardstick, and then covers cluster against string lights, warm white against bright white, and the extension lead and timer basics.
Before you start
Put the tree up and fluff every branch first. Lights go on last, once the shape is settled, because pulling branches into place afterwards drags the wire out of position.
Then plug the lights in and switch them on before they go anywhere near the branches. It is much easier to swap a faulty set when it is lying on the floor than when it is wound around a seven-and-a-half-foot tree.
Decide where the plug will end up. The socket and the base of the tree are where the lead cable has to reach, so work out the route before you wrap anything.
Wrap or weave?
There are two ways to run a string of lights around a tree, and both work.
Wrapping means starting at the bottom and circling the tree, working up in a spiral with the wire sitting on the outer tips of the branches. It is quick, it suits a first-timer, and it gives an even glow from the outside. The downside is that the light sits on the surface, so the tree can look flat from the side.
Weaving means working branch by branch. You take the string along each branch towards the trunk and back out again, so some bulbs sit deep inside the tree and some at the tips. It takes longer, but the tree looks lit from within and the depth is noticeably better, especially on a full tree.
A practical middle route is to weave the lower, wider half of the tree and wrap the narrow top. That is where the most wire is needed, and it is also where a wrapped spiral is easiest to control.
Whichever you choose:
- Start at the bottom, next to the socket, and work upwards. Starting at the top means a long lead hanging down the front of the tree.
- Keep the spacing even, with the same distance between each turn or each branch.
- Finish by tucking the last section and the end of the string into the branches near the trunk.
- Step back after each section and check for dark gaps.
How many lights does your tree need?
There is no official number, so the best guide is what trees sold pre-lit actually carry. These are the figures from the product pages, with the lights per foot worked out from them:
- The 4.5ft Oakley Fir Pre-Lit Mini Tree with 150 Warm White LEDs has 150 warm white LEDs, which is about 33 lights per foot.
- The 7.5ft Feel Real Newberry Spruce Pre-Lit Slim Artificial Christmas Tree has 450 warm white LEDs on a tree 44 inches (112cm) across, which is 60 lights per foot.
- The 7.5ft Elveden Fir Pre-Lit Artificial Christmas Tree has 650 warm white lights on a tree 54 inches (137 cm) across, which is about 87 lights per foot.
So a sensible range runs from roughly 30 lights per foot for a light, tidy look up to around 90 per foot for a tree that glows. Width matters as much as height: the fuller, wider Elveden Fir carries well over a hundred more lights than the slim Newberry Spruce at the same 7.5 feet.
To use the range, multiply your tree’s height in feet by the number you want. A 6ft tree at 60 lights per foot wants about 360 lights. A 7.5ft slim tree at the same density wants about 450. If your tree is full and wide, aim for the top of the range. If it is slim or you like a restrained look, the lower or middle part is plenty.
Count the lights on the box, not the length of the string. Two sets of the same length can carry very different numbers of bulbs.
Cluster lights or string lights?
A standard string has bulbs spaced out along the wire. Cluster lights pack many tiny LEDs close together, so a single string gives a dense, sparkling glow without needing several sets.
The 2040 LED Twinkle Cluster Classic Warm Christmas Lights on Green Cable is a good example. It has 2040 LEDs on 19 metres of cable plus an 8-metre lead cable, which the product page puts at approximately 107 LEDs per metre. It runs 8 twinkle functions including static, has an 8-hour timer and is suitable for indoor and outdoor use. The green cable blends into the branches, which helps when you are weaving.
Cluster lights suit large trees and anyone who wants the full, dense look from one set. Because of how many bulbs there are on each metre, they are also forgiving of uneven spacing. A standard string suits smaller trees, tabletop trees, or a tree where you want a lighter, more traditional spacing. You can browse both styles in our Christmas tree lights category.
If the tree is somewhere without a socket nearby, or you would rather not have a cable trailing across the room, take a look at battery-powered Christmas lights. The 600L Compact Twinkle Durawise Multicolour Battery Lights has 600 LEDs on 14.98 metres of cable and runs on 3 x D size batteries (not included). It has a 6-hour timer and 8 twinkle functions.
Warm white or bright white?
This is a matter of taste, but it helps to know what you are choosing between. Our post on warm white against classic warm lights explains that warm white gives a bright, golden glow, and suits larger trees from 7ft to 12ft. Classic warm has a softer yellow glow that many people call the candlelight effect, and suits small trees and bedrooms.
The one rule worth following is not to mix tones on the same tree. Two shades of white side by side look like a mistake rather than a choice. If you are adding to an old set, buy the new lights in the same colour or replace the lot.
Extension leads and timers
Plan the cable before the first bulb goes on. Measure from the tree to the nearest socket and check that the lead cable on your lights reaches. If it does not, you will need an extension lead, so have one ready rather than discovering the gap once the tree is dressed.
A timer saves you from remembering to switch the tree off. Some lights have one built in: the cluster set above has an 8-hour timer and the battery set has a 6-hour one. If yours does not, a plug-in timer between the socket and the lights does the same job.
Mains lights with a transformer, like the cluster set above, need the transformer to sit somewhere you can reach. Keep it near the plug end rather than buried behind the tree.
Would you rather not do it at all?
If the thought of wrapping a 7.5ft tree is putting you off, a pre-lit Christmas tree arrives with the lights already built in. You still have to plug it in and fluff the branches, but the wiring is done.
Frequently asked questions
Do you put lights on a Christmas tree before or after the decorations?
Lights go on first. Tinsel, baubles and ribbon follow, so the decorations can hide the wire rather than tangle with it.
How many lights do I need for a 6ft tree?
Using the trees above as a guide, between roughly 180 lights for a light look and about 540 for a very bright one. A figure around 360 sits in the middle, at 60 lights per foot.
Which way should you wrap lights on a Christmas tree?
From the bottom up, starting beside the socket. That keeps the lead cable short and puts the plug end where you need it.
Should lights go on the tree from the top or the bottom?
The bottom. Working up means the cable always runs from the socket to the part you are lighting, and any slack ends at the top where it is easy to tuck in.